Регуляторы, системы ЧПУ

Основные характеристики операторской панели (панели оператора) eMT3150A: Дисплей: 15” TFT LCD Цветность: 16.

конструкция: повторитель RS-485 вход: двухпроводной интерфейс RS-485, разъем типа гнездо DB9 выход: интерфейс RS-485 количество портов: 3

Конструкция: модуль с последовательным интерфейсом, монтируется на DIN-рейку, пластиковый корпус Интерфейс: тип: RS-485 скорость передачи

Analog Input Input Channels 10 differential or 20 single-ended (Voltage Inputs Only, Note1), software selectable Input Type +/-150mV, +/-500mV, +/-1V, +/-5V, +/-10V, +/-20mA ,0~20mA, 4~20mA (jumper selectable) Resolution 16-bit (Normal Mode) /

Конструкция: модуль с последовательным интерфейсом, монтаж на DIN рейку, пластиковый корпус Интерфейс: тип: RS-485 скорость передачи данных:

Конструкция: модуль с последовательным интерфейсом, монтаж на DIN рейку, пластиковый корпус Интерфейс: тип: RS-485 скорость передачи данных:

Analog Output Output Channels 4 Output Type 0 ~ 20 mA, 4 ~ 20 mA, 0 ~ 5V, +/-5V, 0 ~ 10V, +/-10V Resolution 14-bit Accuracy +/-0.

Digital Input Input Channels 14 Input Type Sink or Source,Isolated channel with common power or ground Off Voltage Level +1V Max On Voltage Level +4 ~ +30V Input Impedance 3K Ohms, 0.

Digital Input Channels 4 Input Type Sink or Source, Isolated channel with common power or ground Off Voltage Level +1V max.

Digital Input Channels 16 Input Type Dry Contact Source Wet Contact Sink or Source Dry Contact Off Voltage Level Open On Voltage Level Close to GND Effective Distance 500 M Max.

Digital Input Channels 8 Input Type Dry Contact: Source, Wet Contact: Sink or Source Dry Contact Level Off Voltage Level : Open On Voltage Level : Close to GND Wet Contact Level Off Voltage Level : +4V max.

Digital Input Channels 4 Input Type Sink or Source Off Voltage Level +1V max.

Digital Input Channels 8 Input Type Sink, Source, isolated channels with common ground or power Off Voltage Level +1V max.

Interface Input (Master) 1 RS-485 Channel: Data+, Data- Output (Slave) 3 RS-485 Channels: Data+, Data- 2-wire Cabling Belden 8941 (2P twisted-pair cable), if different cables are used, the transmission distance may change Transfer Distance Max.

Models I-7520 I-7520R I-7520A I-7520AR Interface Serial Interface RS-232 TxD, RxD, GND RS-422 - TxD+, TxD-, RxD+, RxD The RS-422 and RS-485 cannot be used simultaneously RS-485 Data+, Data- 2-wire Cabling/4-wire Cabling Belden 8941 (2P twisted-pair

Timer Build-in Watchdog Timer Yes Connector For I-7521/I-7522/I-7523 Male DB-9 For I-7521/I-7522/I-7523 13-pin screw terminal block ( accepts 16~26 AWG wires ); 3.

CAN Interface Transceiver NXP 82C250 AMIS 41682 Channel number 1 Connector 9-pin male D-Sub (CAN_L, CAN_H, N/A for others) Baud Rate (bps) 10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 Mbps 10 k, 20 k, 50 k, 125 kbps Isolation 3000 VDC for

CAN Interface Controller NXP SJA1000T with 16 MHz clock Transceiver NXP 82C250 Channel number 1 Connector 2-pin screwed terminal block (CAN_L, CAN_H) Baud Rate (bps) 10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 M (allow user-defined baud rate)

Interface Input TxD, RxD, CTS, RTS, GND or TxD, RxD, DSR, DTR, GND Jumpers JP1 and JP2 are used to select the RS-232 input source type Output TxD, RxD, CTS, RTS, GND or TxD, RxD, DSR, DTR, GND Transfer Distance Max.

Interface USB Compatibility: USB 1.